| SMT工藝作業指導書中關鍵詞對照 |
| 2007/2/1 16:28:39 產通學院，365PR NET |
|
|
|
|
| |
|
|
1.缺件(MISSING PARTS)
2.錯件(WRONG PARTS)
3.多件(EXCESSIVE PARTS)
4.短路(SHORT)
5.斷路(OPEN)
6.線短(WIRE SHORT)
7.線長(WIRE LONG)
8.拐線(WIRE POOR DDRESS)
9.冷焊(COLD SOLDER)
10.包焊(EXCESS SOLDER)
11.空焊(MISSING SOLDER)
12.錫尖(SOLDER ICICLE)
13.錫渣(SOLDER SPLASH)
14.錫裂(SODER CRACK)
15.錫洞(PIN HOLE)
16.錫球(SOLDER BALL)
17.錫橋(SOLDER BRIDGE)
18.滑牙(SCREW LOOSE)
19.氧化(RUST)
20.異物(FOREIGNER MATERIAL)
21.溢膠(EXCESSIVE GLUE)
22.錫短路(SOLDER BRIDGE)
23.錫不足(SOLDER INSUFFICIENT)
24.極性反(WRONG POLARITY)
25.腳未入(PIN UNSEATED)
26.腳未出(PIN UNVISIBLE)
27.腳未剪(PIN NO CUT)
28.腳未彎(PIN NOT BENT)
29.缺蓋章(MISSING STAMP)
30.缺標簽(MISSING LABEL)
31.缺序號(MISSING S/N)
32.序號錯(WRONG S/N)
33.標簽錯(WRONG LABEL)
34.標示錯(WRONG MARK)
35.腳太短(PIN SHORT)
36.J1不潔(J1 DIRTY)
37.錫凹陷(SOLDER SCOOPED)
38.線序錯(W/L OF WIRE)
39.未測試(NO TEST)
40.VR變形(VR DEFORMED)
41.PCB翹皮(PCB PEELING)
42.PCB彎曲(PCB TWIST)
43.零件沾膠(GLUE ON PARTS)
44.零件腳長(PARTS PIN LONG)
45.浮件(PARTS LIFT)
46.零件歪斜(PARTS TILT)
47.零件相觸(PARTS TOUCH)
48.零件變形(PARTS DEFORMED)
49.零件損壞(PARTS DAMAGED)
50.零件腳臟(PIN DIRTY)
51.零件多裝(PARTS EXCESS)
52.零件沾錫(SOLDER ON PARTS)
53.零件偏移(PARTS SHIFT)
54.包裝錯誤(WRONG PACKING)
55.印章錯誤(WRONG STAMPS)
56.尺寸錯誤(DIMENSION WRONG)
57.二極管壞(DIODE NG)
58.晶體管壞(TRANSISTOR NG)
59.振蕩器壞(X’TL NG)
60.管裝錯誤(TUBES WRONG)
61.阻值錯誤(IMPEDANCE WRONG)
62.版本錯誤(REV WRONG)
63.電測不良(TEST FAILURE)
64.版本未標(NON REV LEBEL)
65.包裝損壞(PACKING DAMAGED)
66.印章模糊(STAMPS DEFECTIVE)
67.標簽歪斜(LABEL TILT)
68.外箱損壞(CARTON DAMAGED)
69.點膠不良(POOR GLUE)
70.IC座氧化(SOCKET RUST)
71.缺UL標簽(MISSING UL LABEL)
72.線材不良(WIRE FAILURE)
73.零件腳損壞(PIN DAMAGED)
74.金手指沾錫(SOLDER ON GOLDEN FINGERS)
75.包裝文件錯(RACKING DOC WRONG)
76.包裝數量錯(PACKING Q’TY WRONG)
77.零件未定位(PARTS UNSEATED)
78.金手指沾膠(GLUE ON GOLDEN FINGERS)
79.墊片安裝不良(WASHER UNSEATED)
80.線材安裝不良(WIRE UNSEATED)
81.立碑（Tomb stoning）
|
|
| → 『關閉窗口』 |
|
| |
|
|
|
|
|
|
